deskthority

Good news!
While I am waiting I started to prepare things amd have some trouble with my KBD75rev2: Where to get an hex file for QMK? It has to be ISO-DE. though...


Remember not to mix the physical layout (ISO) with the national layout (DE) when designing the layout. On https://config.qmk.fm ...

Thanks for the update! Looking forward to building this badboy.

I would like to have a snug fit that will hold the key in place and not be wobbly with a good firm snap in. The measurements posted have been 14mm W x L for an H cut pattern and 13.8507mm.

One reason for this might be if someone was making a design for lasercut acrylic plates. The laser has a ...

PlastikSchnittstelle wrote: Now the spreadsheet is error free (99% sure)!

Will you post a list of all orders before the end, so everyone can check that their order is registered correctly?

I just paid my invoice, but noticed too late that it said SKB75, not SKB65. Not sure if I made a mistake when filling in the form or what happened (it's a bit hard to figure out since you don't get receipts for Google forms).

Anyways, I've sent an email regarding the issue. I assume this is the ...

Not sure if the GB is still actually open, but I finally caved and submitted an order (via the form linked in the reddit post).

The main reason is of course that the final product looks like it will be something really special. But what tipped the scales for me was all the hard work and care ...

Sorry to hear about the non-shows and cancellations. I was unfortunately not able to join this time, but I hope you are able to pull this off anyway. You've been doing a very good job so far!

UPDATE (regarding PLATE-B):

the worst performing kit so far is SKB60-Standard with plate-B with only 6 orders.

I'm not going to tell you how to run your GB, but I just want to mention that 1) this GB has not been properly advertised on Reddit yet, so there are some possible extra orders there ...

also regarding the swap-sockets. you can always get shorter standoffs for my SKB case. now the plate is hold by 5mm standoffs wich makes the caps sink in by 2mm. you can just use 4mm standoffs instead or even 3mm and you would certainly have no trouble with swap-socket-PCBs at any angle.

I haven ...

Nice to see another Norwegian guy! That is a nice looking project.

I use Notepad++ or Sublime Text to edit text files.

The enter key you have is the standard ISO enter key, used in most European keyboard layouts.

Just added to the /dev/tty drop

I see. I will have to think hard about joining R2 of MT3 then

matt3o wrote:

TomKazansky wrote: Elvish set for dev/tty1 (MT3 Round 2) please

working on that

Would that be the only Russian/Elvish set you make, or are you still planning to do a separate run of the kits shown earlier in this thread?

This is a long shot, but does the molds for concave 1u or 2u keys exist? It would be great for space/lower/raise keys for Planck-like keyboards.

matt3o wrote: A new drop will come sooner than I anticipated...

You don't say!

https://www.massdrop.com/buy/massdrop-x ... keycap-set

Any updates?

All the keycaps sets I ordered/group buys I joined last year has now arrived, so I need something new to fill my queue!

I'm guessing everyone affected have received this email, but I thought I'd post it here for everyone to see.
Seems like all international and Colemak/Dvorak sets were affected by the issue with bold legends.

Hi,

We are reaching out regarding your order for the Massdrop x Matt3o /dev/tty MT3 ...

https://matt3o.com/the-cost-of-perfection/

Thank you for sticking with me up to this point. I can tell you that we are already working on a second release and this time we are making sure that everything is in place… At least so I am told.

Will the new set also be produced via MassDrop?
Is this ...

Just received my set yesterday, and here is another example of what the bold international set looks like:
01305222 (Large).JPG

The "Ø" legend also pretty off-center. I haven't had a chance to inspect at all the other keys, but so far it seems like most of them are acceptable, even if some of ...

matt3o wrote: I have a rant coming. hold tight

How's the rant coming?

Very nice! I'm torn between this set and DSA Drifter, but I think I'll have to save my money for the Elvish set.

matt3o wrote: just got news from the manufacturer. they had some issues with the pantone I gave them. Still working on it

Any updates?

Any chance that it will be possible to have a arrow key cluster in the lower right of the 60% boards?

Something like this (ISO version):
keyboard-layout (2).jpg

The highligted keys are the most important, the layout of the rest of the bottom row is not that important for me. But standard 1.25u ...

75% is amazing!

What's the chance of the international kit getting produced?

Could you post a picture of the final elvish set?

There's a short update and a photo of the most recent prototypes over at matt3o's blog: https://matt3o.com/devtty-even-more-prototypes/

Everything is looking good, I can't wait!

No it's not my MT3 profile (unfortunately). It's basically an SA clone, I still don't know how much it differs from the original, I'll let you know as soon as I get samples.

This is a bit off-topic, but are you having trouble with Massdrop regarding rights to the MT3 profile? I would be bummed if ...

Don't forget a 1u R1 keycap for full ISO compability (the "<>" or "\ |" key, between left shift and Z).
isnt it R3? please color it in modifier color tough, that looks way nicer.


I can never get the row numbers right, so I've highlighted the differenes between ANSI and ISO in the attached image ...

Don't forget a 1u R1 keycap for full ISO compability (the "<>" or "\ |" key, between left shift and Z).