Coleco ADAM Keyboard - sliders over rubber domes

[XMIT]

Every now and again my saved eBay search for "vintage keyboards" turns up something interesting. Last week I found a Coleco ADAM keyboard. It did not seem so expensive, so intrigued, I picked it up. It arrived today. Gotta love sellers who use way too much packing material. It took five minutes just to get through the tape alone!

The Coleco ADAM was rated by Maximum PC in 2011 as one of the worst computers of all time:
http://www.maximumpc.com/article/featur ... e#slide-13
Some reviewers say that the keyboard was the highlight of the system

At last the box is open:

DSC_3909.jpg (120.3 KiB) Viewed 19057 times

The keyboard looks to be in good condition. The seller said it was tested working. I may Retr0bright some of the keys - carefully!

DSC_3911.jpg (80.73 KiB) Viewed 19057 times

DSC_3919.jpg (96.46 KiB) Viewed 19057 times

DSC_3920.jpg (144.62 KiB) Viewed 19057 times

DSC_3921.jpg (135.01 KiB) Viewed 19057 times

DSC_3922.jpg (83.55 KiB) Viewed 19057 times

Double shot spherical key caps, and an unrecognized slider. What is this?

DSC_3924.jpg (90.33 KiB) Viewed 19057 times

Well, I had to know. 30 screws and an hour later...

DSC_3954.jpg (86.55 KiB) Viewed 19057 times

DSC_3955.jpg (81.23 KiB) Viewed 19057 times

DSC_3960.jpg (83.97 KiB) Viewed 19057 times

The keyboard does say "Made in Japan" and is from 1983. I wonder if these are Brother or Topre domes?

More and higher quality photos are on the photo album for this keyboard:
https://plus.google.com/photos/10439222 ... 5645246305

[jacobolus]

How far away are those keycaps from being Cherry MX compatible?

[Findecanor]

Cruciform looks bigger and is more into the keycap, where there are also strut that would be in the way. Maybe they would work with the adapters used for the MeC64 keyboard.

I still think the keyboard looks a bit unnecessarily high, though. How does it look next to a Commodore C64C ?

[Stabilized]

How does it feel to type on?

[XMIT]

How far away are those keycaps from being Cherry MX compatible?

Quite. The Coleco key caps have a cruciform recess that is too large for Cherry MX switches, and buried too deeply into the key cap itself to press the switch mechanism at all without bottoming out. The Coleco sliders are too large to accept Cherry MX keys. I tried!

[XMIT]

How does it feel to type on?

Much better than I thought it would. These are a high quality rubber dome. They are not quite as nice as Topre rubber domes but they are nicer than Model M Quiet Touch rubber domes. They are Made in Japan after all. The sliders seriously need some lubrication though, the same as a Cherry slider. I've heard some variant of Krytox works well - any suggestions?

[seebart]

Awesome XMIT, I love it! Japanese 80`s high quality domes in a compact case.

[Stabilized]

Much better than I thought it would. These are a high quality rubber dome. They are not quite as nice as Topre rubber domes but they are nicer than Model M Quiet Touch rubber domes. They are Made in Japan after all. The sliders seriously need some lubrication though, the same as a Cherry slider. I've heard some variant of Krytox works well - any suggestions?

You might want to try a light lubricant like 103/104, as they are non viscous and non sticky (unlike something like 106). Either should be easy to get in the US (I think), just use it sparingly on each slider and you should be good

Have you checked out what you will need to get it work on a modern computer?

[XMIT]

Have you checked out what you will need to get it work on a modern computer?

But of course, this is always my goal. The keyboard uses a weird signaling protocol that is documented elsewhere online. The Google album photos show that this is just a single membrane. Very interesting construction: it is one membrane, folded in half. This one seems like an ideal candidate for a controller replacement.

I have a bunch of keyboards that also need controllers, so, I will begin researching the existing controller options in the next couple of weeks. Given the choice I prefer replacement controllers to reduce latency and avoid any odd key combination or mode quirks. Some purists would prefer converters over controllers. To each their own!

[XMIT]

You might want to try a light lubricant like 103/104, as they are non viscous and non sticky (unlike something like 106).

Hmm. I wonder if a mix of Krytox GPL 103 oil and Krytox GPL 205 grease would be better:
https://www.youtube.com/watch?v=eRvtLEZJFKM

Granted, I don't have experience with either one. If someone has some spare of either of these that they want to part with please send me a PM.

I do have some "EK MechLube 2" already. I found that to be way too thick, but perhaps applied very thinly it would work better. I'll do some experiments at home.

My new Topre keyboard has lubricated stabilizers. I wonder what they use?

If I were building a key switch I would look into using Delrin (POM) for any stems. It is a self lubricating, kind of oily plastic.

[Redmaus]

Vintage topre! Neat.

[mr_a500]

Thanks for posting photos, XMIT. I always wondered about the switches in this.

I remember back in 1984/85, these ADAM computers were super cheap because they failed to sell and stores just wanted them gone. I was tempted to get one, but they seemed obsolete already by that time, so I passed.

[XMIT]

I remember back in 1984/85...

I don't! This keyboard is older than I am!

[lee4hmz]

I did some looking into this (including buying one of the bare, Archer-branded ADAM keyboard mechanisms that show up on eBay from time to time), and it looks like whoever made the ADAM keyboard also made the TRS-80 Color Computer I keyboard c. 1980. It has the same domes, but uses a dome-over-leaf-spring construction I've never seen before, and seems to be design number FK-5302. (The CoCo keyboards really deserve their own threads, but I don't have one handy and the computers themselves are increasingly rare these days, so imagine what finding just the keyboard is like). Also, the slider on the ADAM keyboard looks like it might fit Futaba MD keycaps, though on the ADAM, the mount is turned 90 degrees. Unfortunately, I don't have any other MD-compatible caps to check with.

Anyway, what I'm getting at is that I'm pretty sure these keyboards weren't made by Brother or Topre or even Mitsumi like a lot of cheap home-computer keyboards were; I'm thinking they're Futaba-Sejin designs (which would explain the "FK" and "JFK" nomenclature).

[M9HM]

https://www.youtube.com/watch?v=wni4_n-Cmj4

[Palatino]

Have you checked out what you will need to get it work on a modern computer?

But of course, this is always my goal. The keyboard uses a weird signaling protocol that is documented elsewhere online. The Google album photos show that this is just a single membrane. Very interesting construction: it is one membrane, folded in half. This one seems like an ideal candidate for a controller replacement.

I have a bunch of keyboards that also need controllers, so, I will begin researching the existing controller options in the next couple of weeks. Given the choice I prefer replacement controllers to reduce latency and avoid any odd key combination or mode quirks. Some purists would prefer converters over controllers. To each their own!

Did you have any luck getting this keyboard to work with a modern computer?

[MMcM]

Have you checked out what you will need to get it work on a modern computer?

But of course, this is always my goal. The keyboard uses a weird signaling protocol that is documented elsewhere online. The Google album photos show that this is just a single membrane. Very interesting construction: it is one membrane, folded in half. This one seems like an ideal candidate for a controller replacement.

I have a bunch of keyboards that also need controllers, so, I will begin researching the existing controller options in the next couple of weeks. Given the choice I prefer replacement controllers to reduce latency and avoid any odd key combination or mode quirks. Some purists would prefer converters over controllers. To each their own!

Anyone looking to implement a converter instead of a controller should be aware that the keyboard just sends ASCII: all the shift processing is inside the 6801. There are no shift states or up transitions.

I've been meaning to write up the details of experiments with the "weird signaling protocol," which is command-response over a half-duplex serial bus. I put them in this topic which featured other UART tricks.

Did you have any luck getting this keyboard to work with a modern computer?

I did USB as a serial port, since it's just characters. It could be changed to use the TD Keyboard class, but the available data isn't really enough for a modern OS. For that, the controller replacement route is needed.

[lee4hmz]

I did some looking into this (including buying one of the bare, Archer-branded ADAM keyboard mechanisms that show up on eBay from time to time), and it looks like whoever made the ADAM keyboard also made the TRS-80 Color Computer I keyboard c. 1980. It has the same domes, but uses a dome-over-leaf-spring construction I've never seen before, and seems to be design number FK-5302. (The CoCo keyboards really deserve their own threads, but I don't have one handy and the computers themselves are increasingly rare these days, so imagine what finding just the keyboard is like). Also, the slider on the ADAM keyboard looks like it might fit Futaba MD keycaps, though on the ADAM, the mount is turned 90 degrees. Unfortunately, I don't have any other MD-compatible caps to check with.

Anyway, what I'm getting at is that I'm pretty sure these keyboards weren't made by Brother or Topre or even Mitsumi like a lot of cheap home-computer keyboards were; I'm thinking they're Futaba-Sejin designs (which would explain the "FK" and "JFK" nomenclature).

And this gets weirder. It seems like the "JFK/FKJ" nomenclature that this board's matrix uses has shown up in a bunch of other keyboards, mostly by or related to Silver Reed; I'm wondering now if Silver Reed or another Seiko Group company built these. Also, pretty much all of the other keyboards use the Brother/Topre-like round mount; I'm wondering if Coleco was going to use mechanical keyswitches in this board (probably Futaba MA or Alps?), but had to switch to the slider-over-membrane design due to cost.