Phantom Custom Keyboard Group Buy (CLOSED)
- litster
- Location: Washington State, USA
- Main keyboard: KMAC2, The Cheat
- Favorite switch: Brown, Topre, Red, BS
- DT Pro Member: -
Just make another one?
I have most of the design QCAD. I need to make room for the Teensy and rout the cable to the back. Also made room for the 6-pin connector on a real Filco. The case would work for both Phantom and Filco. I could get it laser cut using Acrylic instead of cardboard.
I have most of the design QCAD. I need to make room for the Teensy and rout the cable to the back. Also made room for the 6-pin connector on a real Filco. The case would work for both Phantom and Filco. I could get it laser cut using Acrylic instead of cardboard.
- litster
- Location: Washington State, USA
- Main keyboard: KMAC2, The Cheat
- Favorite switch: Brown, Topre, Red, BS
- DT Pro Member: -
Now I have it in QCAD.
Top layer: For Filco Tenkeyless, this layer needs to be thicker to raise the top layer higher because of Filco's controller. This layer can be thinner for Phantom since its controller is under the PCB: Cut out for Phantom's controller on the left, Filco's 5-pin plug on the right, plus cable routing. I need to know how much the Teensy controller stick out from the keyboard PCB because I can tell how thick this layer need to me. The bottom layer: If it is made with transparent acrylic and you look at it through the bottom layout, it would like like this: Hum, I think I need to add a screw hole...
EDIT: Added another screw hole, and now a 7bit top layer. EDIT2: LOL! I have a bug in one of the layouts. I will have to fix it or it would look goofy.
Top layer: For Filco Tenkeyless, this layer needs to be thicker to raise the top layer higher because of Filco's controller. This layer can be thinner for Phantom since its controller is under the PCB: Cut out for Phantom's controller on the left, Filco's 5-pin plug on the right, plus cable routing. I need to know how much the Teensy controller stick out from the keyboard PCB because I can tell how thick this layer need to me. The bottom layer: If it is made with transparent acrylic and you look at it through the bottom layout, it would like like this: Hum, I think I need to add a screw hole...
EDIT: Added another screw hole, and now a 7bit top layer. EDIT2: LOL! I have a bug in one of the layouts. I will have to fix it or it would look goofy.
- wcass
- Location: Columbus, OH, USA
- Main keyboard: ibm model m
- Main mouse: kensington expert mouse
- Favorite switch: buckeling spring
- DT Pro Member: 0185
measurements taken from teensy 2 with pins.
51.01mm x 17.74mm
from bottom of pin header to top of pcb: 4.66mm
from bottom of pin header to top of usb: 8.16mm
length of pins: 5.87mm
let me know if you need pictures
51.01mm x 17.74mm
from bottom of pin header to top of pcb: 4.66mm
from bottom of pin header to top of usb: 8.16mm
length of pins: 5.87mm
let me know if you need pictures
- litster
- Location: Washington State, USA
- Main keyboard: KMAC2, The Cheat
- Favorite switch: Brown, Topre, Red, BS
- DT Pro Member: -
wcass, your measurements for length and width look like Teensy++, is that correct? But I think the height should be the same between Teensy and Teensy++. Do you have the height measurement between the keyboard PCB (not the Teensy PCB) and the top of the USB connector, as if the Teensy with pins is soldered onto a keyboard PCB? Thanks.
- wcass
- Location: Columbus, OH, USA
- Main keyboard: ibm model m
- Main mouse: kensington expert mouse
- Favorite switch: buckeling spring
- DT Pro Member: 0185
yes, Teensy++ 2.0 - i have a Teensy around here somewhere, but can't find it right now.
from bottom of pin header (keyboard pcb) to top of teensy pcb: 4.66mm
from bottom of pin header (keyboard pcb) to top of usb: 8.16mm
from bottom of pin header (keyboard pcb) to top of teensy pcb: 4.66mm
from bottom of pin header (keyboard pcb) to top of usb: 8.16mm
- litster
- Location: Washington State, USA
- Main keyboard: KMAC2, The Cheat
- Favorite switch: Brown, Topre, Red, BS
- DT Pro Member: -
Thanks wcass. I think they have similar thickness. Your numbers are very helpful. I can use it for getting a quote for cutting the plates. I also ordered a Teensy 2.0 that should arrive Tuesday or Wednesday as it is only about 300 miles away from me.
-
- Location: Germany
- DT Pro Member: -
We could need one version of the top layer more:
All plates have the holes for the five additional keys above the arrow keys, but
- the standart top layer does not support these keys
- the 7bit top layer does support them, but the Fx-row is not devided
So we would need a version with devided Fx-row and full block above the arrows!
All plates have the holes for the five additional keys above the arrow keys, but
- the standart top layer does not support these keys
- the 7bit top layer does support them, but the Fx-row is not devided
So we would need a version with devided Fx-row and full block above the arrows!
- litster
- Location: Washington State, USA
- Main keyboard: KMAC2, The Cheat
- Favorite switch: Brown, Topre, Red, BS
- DT Pro Member: -
Tarkoon, drawing that layer is a 2 minute job. That's easy. Adding another item to the parts list is more problematic. If the first prototype case turns out OK, we will see what we can do next.
-
- Location: Stockholm, Sweden
- DT Pro Member: 0011
I'm thinking of making myself a case out of oak, but I anticipate that the narrow space in-between the main and arrow clusters could be problematic.
I have saved the case of my old Key Tronic KT-800 and maybe that case would fit the Filco/Phantom innards ... Only a little plastic surgery required.
I have saved the case of my old Key Tronic KT-800 and maybe that case would fit the Filco/Phantom innards ... Only a little plastic surgery required.
- 7bit
- Location: Berlin, DE
- Main keyboard: Tipro / IBM 3270 emulator
- Main mouse: Logitech granite for SGI
- Favorite switch: MX Lock
- DT Pro Member: 0001
Me too;-)Gilgam wrote:i wanted to make one in wood too
how do you think it can be ? (i have no skills at all, but i can learn )
I recommend to just get a backplate plus a frame around it, but I'm no expert either
-
- Location: Stockholm, Sweden
- DT Pro Member: 0011
I don't have many skills either, mostly 20 year old memories from wood class in school and a few ideas. I tried some wood-staining recently, on a (ready-made) box and a chair, and I liked that result
A challenge would be to keep the grain in mostly one direction and not expose any end grain, because if you stain it, then end grain usually stains darker than the rest.
First, I think that I would construct a frame, in the same manner as a picture frame is constructed: cut strips of wood (some ready-made wooden trim) at 45° angles and glue together. Then, I would cut a 7mm thick wide plank into a single piece (if possible) to fit in-between the key groups and friction fit/glue this in. I anticipate that there will be a lot of adjusting it back and forth. Maybe I would have to cut and glue several small pieces of wood together, or in the worst case: use some other material and oak veneer (the horror).
I am not sure how to make the bottom. For myself, I want a keyboard that is as flat and low as possible with smooth sides. I think that I could perhaps make a ledge (by chiselling or routing) around the inside of the bottom of the frame and mostly friction-fit a rectangular piece of plywood, aluminium or plastic in there and secure it to the top with a few bolts through the holes in the PCB/plate that thread into metal grommets secured in the bottom of the top. The bottom would need to have a recess in it for the Teensy, but I think that it could be achieved by layering.
A challenge would be to keep the grain in mostly one direction and not expose any end grain, because if you stain it, then end grain usually stains darker than the rest.
First, I think that I would construct a frame, in the same manner as a picture frame is constructed: cut strips of wood (some ready-made wooden trim) at 45° angles and glue together. Then, I would cut a 7mm thick wide plank into a single piece (if possible) to fit in-between the key groups and friction fit/glue this in. I anticipate that there will be a lot of adjusting it back and forth. Maybe I would have to cut and glue several small pieces of wood together, or in the worst case: use some other material and oak veneer (the horror).
I am not sure how to make the bottom. For myself, I want a keyboard that is as flat and low as possible with smooth sides. I think that I could perhaps make a ledge (by chiselling or routing) around the inside of the bottom of the frame and mostly friction-fit a rectangular piece of plywood, aluminium or plastic in there and secure it to the top with a few bolts through the holes in the PCB/plate that thread into metal grommets secured in the bottom of the top. The bottom would need to have a recess in it for the Teensy, but I think that it could be achieved by layering.
- Gilgam
- Location: france
- Main keyboard: Too many
- Main mouse: CST trakball
- Favorite switch: red ?, maybe topre, well no, black... Or brown???
- DT Pro Member: -
thanks for your detailed answer
i have the nearly same idea but i have to check that pcb and teensy before (or i'll try with a cut g80-1800).
i have the nearly same idea but i have to check that pcb and teensy before (or i'll try with a cut g80-1800).
- litster
- Location: Washington State, USA
- Main keyboard: KMAC2, The Cheat
- Favorite switch: Brown, Topre, Red, BS
- DT Pro Member: -
I got lucky and found a way to get access to a laser cutter tonight. But I can't mass produce because I don't have access to the laser cutter at will. I need to refine the drawing to make it fit better. But right now it is very close to my expectation. One thing I won't do in the future is to cut the "Phantom" word on the 3rd layer because that took a LOOOOONG time to cut. Speed had to be slowed down because that piece is so thick. Engraving maybe a possibility.
Then we can find a shop to cut it. It will be over $200 though unless we find some shop that is cheaper.
Then we can find a shop to cut it. It will be over $200 though unless we find some shop that is cheaper.
- litster
- Location: Washington State, USA
- Main keyboard: KMAC2, The Cheat
- Favorite switch: Brown, Topre, Red, BS
- DT Pro Member: -
A couple more pictures:
Thing I need to do or think about:
- 2nd layer needs to be a tad thicker for Filco. Not a problem with the actual Phantom.
- lower screws count from 11 to 8, don't really need that many screws.
- right now the PCB is sitting on the bottom later. A better way to do this is to glue a few acrylic posts to support the plate instead. Need to engrave the post positions. Notices the PCB has already scratched the bottom layer. If we do this, the 3rd layer needs to be thicker.
- need to move the cable cut out to center. I underestimated how long the cable is.
- the second layer needs to be a tad wider and longer than it is now. maybe 0.5mm. Right now it is a super tight fit. Need final plate and PCB to determined final size.
- Need to back legs. Currently it is too flat.
- The top layer is OK, but I can move some key holes a little bit to center the holes to keycaps. Need to way for the final plate cut to determine final key hole locations.
Round out the inside corners for the 3rd layer.
- I need better screws. Please, any suggestions for better screws? these from Lowe's sucks. They are too long and I had to Dremel them.
- I got my Teensy today. The 3rd layer's thickness is perfect.
- should we make the case both Phantom and Filco compatible?
- as much as I have cut out, the case is HEAVY! Is that good?
- the Phantom wording took a long time to cut, especially because that layer is so thick, the laser need to run slower to cut it. It barely cut through. For the final version, I don't think the word Phantom will be cut. Maybe engraved.
Thing I need to do or think about:
- 2nd layer needs to be a tad thicker for Filco. Not a problem with the actual Phantom.
- lower screws count from 11 to 8, don't really need that many screws.
- right now the PCB is sitting on the bottom later. A better way to do this is to glue a few acrylic posts to support the plate instead. Need to engrave the post positions. Notices the PCB has already scratched the bottom layer. If we do this, the 3rd layer needs to be thicker.
- need to move the cable cut out to center. I underestimated how long the cable is.
- the second layer needs to be a tad wider and longer than it is now. maybe 0.5mm. Right now it is a super tight fit. Need final plate and PCB to determined final size.
- Need to back legs. Currently it is too flat.
- The top layer is OK, but I can move some key holes a little bit to center the holes to keycaps. Need to way for the final plate cut to determine final key hole locations.
Round out the inside corners for the 3rd layer.
- I need better screws. Please, any suggestions for better screws? these from Lowe's sucks. They are too long and I had to Dremel them.
- I got my Teensy today. The 3rd layer's thickness is perfect.
- should we make the case both Phantom and Filco compatible?
- as much as I have cut out, the case is HEAVY! Is that good?
- the Phantom wording took a long time to cut, especially because that layer is so thick, the laser need to run slower to cut it. It barely cut through. For the final version, I don't think the word Phantom will be cut. Maybe engraved.
- Half-Saint
- Location: Slovenia, Europe
- Main keyboard: Raptor Gaming K1
- Main mouse: Logitech G5 Mk.2
- Favorite switch: Cherry MX Blue
- DT Pro Member: 0058
Sweet acrylic case
Why would I want to choose 7bit's layout? Those huge top row keys don't really make all that much sense to me.
Why would I want to choose 7bit's layout? Those huge top row keys don't really make all that much sense to me.
- mrog
- Location: Berkshire, UK
- Main keyboard: Dell AT102W - Seeking other keyboards
- Main mouse: Logitech G5
- Favorite switch: Buckling Spring
- DT Pro Member: -
Hi, I'm new to the boards - I found it while looking for IBM Model M keyboards for sale (still looking for a ISO/UK layout). From what I gather in the posts here and on geekhack - the phantom was designed to create a replacement board for the felco so that cherry switches can be used throughout so you can use doubleshot injection molded keycaps?
It looks like now you've got all the parts to throw together a complete keyboard - or are you still harvesting parts from other complete keyboards?
I currently have no mechanical keyboard - but I grew up using a IBM model M, so have no parts.
I guess what I'm asking is - is it feasible for me to get involved in this and source all the parts required to make my own keyboard - with my choice (or design) of key cap, switch, layout and case while maintaining a reasonable price?
Sorry if any of my questions are misinformed - I'm very new to mechanical keyboards and I can't believe I've found people with the same fanaticism with user input devices as me - I've been reading the forum for two days straight (don't tell my boss).
You guys are great - I'm really glad I found this place.
It looks like now you've got all the parts to throw together a complete keyboard - or are you still harvesting parts from other complete keyboards?
I currently have no mechanical keyboard - but I grew up using a IBM model M, so have no parts.
I guess what I'm asking is - is it feasible for me to get involved in this and source all the parts required to make my own keyboard - with my choice (or design) of key cap, switch, layout and case while maintaining a reasonable price?
Sorry if any of my questions are misinformed - I'm very new to mechanical keyboards and I can't believe I've found people with the same fanaticism with user input devices as me - I've been reading the forum for two days straight (don't tell my boss).
You guys are great - I'm really glad I found this place.
- trax
- Location: Belgium
- Main keyboard: HHKB Pro 2 Type-S
- Main mouse: ZOWIE FK2
- Favorite switch: Topre
- DT Pro Member: -
Dear handymen,
if any of you can make me a full, finished phantom keyboard please let me know.
I'll pay all the costs you need to make, and obviously a good price for the hard work you'd make.
If anyone is interested in making some cash over this, please send me a PM.
trax.
if any of you can make me a full, finished phantom keyboard please let me know.
I'll pay all the costs you need to make, and obviously a good price for the hard work you'd make.
If anyone is interested in making some cash over this, please send me a PM.
trax.
- webwit
- Wild Duck
- Location: The Netherlands
- Main keyboard: Model F62
- Favorite switch: IBM beam spring
- DT Pro Member: 0000
- Contact:
That looks really great.litster wrote:A couple more pictures: