HyperMicro madness

[Nuum]

Which one is that, matt3o? I have a plate design ready that needs to be cut out and bent.

[ne0phyte]

You can still cancel the order

[7bit]

I did not yet order!

[matt3o]

or send me the DXF file + quantities and I'll make you a quotation.

[7bit]

Done.

These are the version that does not require any bending.

[suka]

Teaser alert: Case ready, details later...

[7bit]

Just as an info for you:
The mount plate will have precisely the same dimensions like the PCB, except for the bottom.

Looking at your case, it seems I should let them cover the complete PCB.

[suka]

I don't really see the point of a plate with such a tiny pcb - since it is supported by a small ridge all around and further supports underneath there is no bending at all. But of course I plan to fill the gap in the front and any possible free areas to the sides for other switch layouts

But so far I'm glad I managed to build a solid base on the first try so I don't have to carry around that foam mat any more. Some measurements are still a little off but nothing really upsetting or inhibiting daily usage.

Inside with trackpoint holder, micro usb adaptor and support ridges

hm_inside.JPG (746.55 KiB) Viewed 7956 times

Top view, front still to be covered

hm_top.JPG (515.12 KiB) Viewed 7956 times

side view

hm_side.JPG (255.61 KiB) Viewed 7956 times

[matt3o]

I don't really see the point of a plate with such a tiny pcb

the plate IS the case

[Halvar]

Sorry for posting this so late -- I got the prototype, switches and caps I won from 7bit. Thanks again 7bit! Some nice extra caps, too, I'll have to see what I can make of them layout-wise, one should maybe be usable as a space bar.

Which thread should I read to know what to do to assemble it, especially about the trackpoint? The interest check?

I understand that the prototype has been shown to work ok, right? Any caveats besides the small gaps and the teensy LED?

[7bit]

There is just a hole (2 actually) for the trackpoint, so you are on your own with that.


The best general guide is the one about the Phantom (wiki).

[Muirium]

I nagged poor Matto and Suka for advice. I'm almost done construction now: diodes and switches are in. So I'll be more help when I'm finished, too.

Mine won't have the track point, unless someone sources one for me.

[Halvar]

Phantom page does look like a good start, thanks!

http://deskthority.net/wiki/Phantom_instruction_guide

[scottc]

That case looks great, Suka! Did you 3d print it?

[suka]

That case looks great, Suka! Did you 3d print it?

Indeed I did

[scottc]

That case looks great, Suka! Did you 3d print it?

Indeed I did

Out of interest, did you do it yourself or get it done by Shapeways or similar?

[suka]

It was built on the same machines as shapeways uses with the strong and flexible material. Once done, I'll plan on also making it available there.

[Halvar]

Sorry if I continue to ask dumb questions, but this is the first keyboard I build, please bear with me ...

I have now soldered on the switches and diodes and a "socket" for the Teensy. Before I go on with soldering the Teensy I have some questions...

@matteo, @suka, @7bit: I assume you use hasu's firmware? Is there any documentation on the Teensy pin assignments on the HyperMicro (or is everyone just looking at traces on the pcb and using his multimeter to find out?)

Care to share some config files etc.?

EDIT: the microswitch buttons (mouse buttons) seem to be connected on the PCB so that the circuit is closed when not pressed. Do I have the wrong switches? I tried the microswitches in several old mice that I have here, which all fit mechanically, but they all connect the center contact to one of the outer contacts when pressed vs. the two outer contacts when released.

[suka]

I am using my own firmware, but with inverted diode direction. Row and column assignments of the first prototype are documented in the latest commits, but a general spec with any other connections like for the LEDs is still missing.

As for the mouse buttons: just cut one outer pin of the switch and bridge the unused center pad to the side.

[matt3o]

Code: Select all

 * col: 0   1   2   3   4   5   6   7   8   9   10  11
 * pin: D6  D4  D7  B4  B5  B6  D5  B3  B2  F4  F1  F0

Code: Select all

 * row: 3   2   1   0
 * pin: F7  B7  B1  B0

I'll post the full code tomorrow

[Halvar]

Thanks suka & matteo!

@matteo: I see you soldered in some microswitches as mouse buttons. Did you get them to work in the meantime? I wonder if 7bit should maybe change the pin assignment for these in the next version of the PCB. I think with the common assigment of these pins (including Cherry DG microswitches) the current tracing is wrong.

Can you define keys as being NC (normally connected) in hasu's firmware?

Edit: sorry, nvm, I just saw that 7bit already wrote that in one of the other threads.

[7bit]

suka, I need the angle of your case!


edit:
I've measured about 6 degrees.

[matt3o]

attached the firmware I used (sorry I don't remember if that is the latest version, bust should get you started).

You'll also find the already compiled version if you are in a hurry. I created it over the GH60 files. Simply place the folder inside the keyboards folder and "make KEYMAP=plain".

[7bit]

What is a folder?

Spoiler:

[matt3o]

"directory", youngsters call it "folder"

to make it even clearer.

1. download hasu's firmware https://github.com/tmk/tmk_keyboard
2. unzip my firmware, if you want rename the directory to "hypermicro"
3. copy the directory inside the "keyboards" directory
4. cd to the directory
5. "make clean" (just for the sake of it)
6. "make KEYMAP=plain"
7. you'll end up with a .hex file you can burn into the Teensy

[7bit]

__MACOSX/gh60


It contains some binaries, what do we have to do with them?

[matt3o]

trash the __MACOSX directory. That is nonsense created by a stupid OS. Sorry about that. I updated the zip from a better system, you can redownload it if you want.

[7bit]

I've renamed some things within the former GH60 directory, which is now hypermicro.

Ideally, once we have the keyboard layouts for all types of hypermicro, the hypermicro directory should be added to the tmk_keyboard-master project.


What is this LUFA vs. PJRC thing?

[matt3o]

that's the USB library. LUFA seems much better and always updated, pjrc is the default USB stack created for the teensy, probably limited but it works.

I'll work on the final firmware as soon as I get the final PCB

[7bit]

I already cleaned it up as much as I could.


I still have to figure out how the 7BIT-layout should look like ...


To be spit and unpacked into tmk_keyboard-master/keyboard/