Phantom Custom Keyboard Group Buy (CLOSED)

[xbb]

Tomorrow I need to change my order, could you write somewhere in the first posts all the order codes or they are somewhere else?
Thanks!

[litster]

Tomorrow I need to change my order, could you write somewhere in the first posts all the order codes or they are somewhere else?
Thanks!

Should be all here:

Here is the link to the pricelist:
http://deskthority.net/wiki/Phantom#Pricelist

I will add this to the first page as well.

[xbb]

great thanks a lot

[HzFaq]

Hi,

I just ordered an ISO kit (PHISOREDKIT), do I need to order any diodes or anything extra (aside from caps and a case obv)?

Cheers,

Tom

[7bit]

Hi,

I just ordered an ISO kit (PHISOREDKIT), do I need to order any diodes or anything extra (aside from caps and a case obv)?

Cheers,

Tom

TEENSY
PHANTOM
PH(ANSI, ISO etc)
MX(red green blue black brown clear) 96
DIODE 96
STAB200 3 or 4
STAB625 or STAB700

You get 2 white LEDs along with the PHANTOM PCB.

[mintberryminuscrunch]

is there a confirmation email after sending my address?
btw. I hope you don´t start collecting money at the same time as the gb4

[7bit]

is there a confirmation email after sending my address?

No, but I will include your address in the invoice I will send out next week, once we've got the definitive prices for switches.

[trax]

Is it possible to get more leds?

[litster]

Maybe possible. How many more do you need?

[gimpster]

So what's the status on the cases, exactly? The list on GH still shows them on the order options list, but it looks like 7bit is saying they're not available on this thread...also, I read through the last few pages, but it's not quite clear which stabilizers (Cherry or Costar) will come with the kits. Also curious if the Dark Gray switches (to go with Red and Black switches) are available.

[litster]

Case: not available, will be removed from invoice if ordered previously
Stabilizers: most likely Costar for 2x and 6.25x. For 7x, also Costar, but yours truly will be bending 7x stabilizer bars. Totally dreading the work of bending 40 or them...
Grey switch: not on the price list on 7bit's Phantom wiki http://deskthority.net/wiki/Phantom. 7bit?

[litster]

Kits include the following:
1 PCB (includes 2 white LEDs and2 resistors)
1 Plate
1 Teensy (includes 1 40-pin pin header)
100 switches
100 diodes
4 2x stabilizers for ANSI or 3 2x stabilizers for ISO or 0 for PH7BIT
1 7x or 1 6.25x stabilizer set for spacebar or 0 for PH7BIT

Pricing will be the same as if you order them separately. Finally pricing is not completely locked yet. 7bit will adjust pricing in his script later when we finalize it.

[7bit]

If someone experienced that he sent an order but got something totally different, please contact me!

7bit.

[gimpster]

Case: not available, will be removed from invoice if ordered previously
Stabilizers: most likely Costar for 2x and 6.25x. For 7x, also Costar, but yours truly will be bending 7x stabilizer bars. Totally dreading the work of bending 40 or them...

Excellent info. Time to get my soldering skills warmed up since I'm going to be doing 2 of these keyboards.

Grey switch: not on the price list on 7bit's Phantom wiki http://deskthority.net/wiki/Phantom. 7bit?

7bit: did you see this question? I just want to confirm whether the GRAY and DARK GRAY switches are available. If not through this group buy, then if anyone can point me to a good source where I can order just 2 of each, for reasonable prices, then I'd appreciate it.

[7bit]

I've removed them before I discovered that grey switch (grey 39 MX1A-D1NN) thread on GH. I will add them again and price will be $0.8 to $0.6 depending on quantity.

Which is MXGREY and which MXDARKGREY ????

[gimpster]

MXGREY is tactile and used with browns and clears
MXDARKGREY is linear and used with blacks and reds

Not sure if that helps clear up the confusion with the ordering.

[xbb]

should I wait that you update the price list before I modify my order?

[digitalleftovers]

I received an invoice that included a price for MX Greens. Does this mean a source has been found for these? I'm wondering because if they can't be found for less than 1eur each, then I will just change my order to Blues.

[gimpster]

Just got my invoice. It didn't have the MXGREY or MXDARKGREY on there yet (but I assume you haven't had time to update it to include those yet). However, it also didn't have the PHANTOMMOD150. Is that still available?

[7bit]

MXGREY is tactile and used with browns and clears
MXDARKGREY is linear and used with blacks and reds

Not sure if that helps clear up the confusion with the ordering.

I need Cherry product codes for both.

I only have:
MXGREY MX1A-D1NN
This is the switch from the GH thread.

[7bit]

I received an invoice that included a price for MX Greens. Does this mean a source has been found for these? I'm wondering because if they can't be found for less than 1eur each, then I will just change my order to Blues.

Currently, they are at 0.6 EUR (or $0.8).

If there are at least 900 switches ordered, proce will get down to 0.45 EUR (or $0.6).

[7bit]

Just got my invoice. It didn't have the MXGREY or MXDARKGREY on there yet (but I assume you haven't had time to update it to include those yet). However, it also didn't have the PHANTOMMOD150. Is that still available?

I've moved these over to the Round 4 key caps group buy. There is no way I will have the key caps when all the switches, PCBs, plates etc. arrive.

[gimpster]

Just got my invoice. It didn't have the MXGREY or MXDARKGREY on there yet (but I assume you haven't had time to update it to include those yet). However, it also didn't have the PHANTOMMOD150. Is that still available?

I've moved these over to the Round 4 key caps group buy. There is no way I will have the key caps when all the switches, PCBs, plates etc. arrive.

No problem. I'll make sure to update my order there.

[gimpster]

MXGREY is tactile and used with browns and clears
MXDARKGREY is linear and used with blacks and reds

Not sure if that helps clear up the confusion with the ordering.

I need Cherry product codes for both.

I only have:
MXGREY MX1A-D1NN
This is the switch from the GH thread.

The GH Cherry MX Switch wiki lists the GREY (aka "light" grey) as the MX1A-D and the DARKGREY as the MX1A-2.

Cross-referencing that with the Cherry Corp site (scroll to the bottom) confirms the remaining part numbers ("1NN") as specifying a standard, no LED, no diode, no pins key switch. So, that means the part numbers should be:

GREY: MX1A-D1NN
DARKGREY: MX1A-21NN

That brings up a question I saw asked elsewhere in one of these threads but didn't see an answer to: will this PCB support using LED key switches if we wish? I'd kind of like to do one of mine with LEDs if possible...

[digitalleftovers]

]Currently, they are at 0.6 EUR (or $0.8).

If there are at least 900 switches ordered, proce will get down to 0.45 EUR (or $0.6).

You are awesome.

[litster]

That brings up a question I saw asked elsewhere in one of these threads but didn't see an answer to: will this PCB support using LED key switches if we wish? I'd kind of like to do one of mine with LEDs if possible...

There are LED soldering pads for in-switch LEDs for Capslock and Scroll Lock switch locations only.

[gimpster]

That brings up a question I saw asked elsewhere in one of these threads but didn't see an answer to: will this PCB support using LED key switches if we wish? I'd kind of like to do one of mine with LEDs if possible...

There are LED soldering pads for in-switch LEDs for Capslock and Scroll Lock switch locations only.

Good to know, thanks Lit. At least that saves me the trouble of trying to find double-shot clear caps...

[7bit]

...

GREY: MX1A-D1NN
DARKGREY: MX1A-21NN

That brings up a question I saw asked elsewhere in one of these threads but didn't see an answer to: will this PCB support using LED key switches if we wish? I'd kind of like to do one of mine with LEDs if possible...

I will ask for these. I'm not sure if these are available.

[digitalleftovers]

There are LED soldering pads for in-switch LEDs for Capslock and Scroll Lock switch locations only.

While there may not be soldering pads at other locations, conceivably, I could just run wiring to them, right? Not sure how feasible that is for more than a couple of switches, but it shouldn't be impossible. Maybe glue a little pad down there or something.

[litster]

phantomPCB_HightlightedSmall.jpg (885.55 KiB) Viewed 4677 times

Here is picture of the backside of the PCB, with interesting areas highlighted. I also highlighted diode locations that are no the same as the majority ones. Need to make sure your diodes are at the right polarity. Check it out.