IDENTIFY THE KEYBOARD thread

[motoko]

Looks like the terminal to Mother on the Nostromo!

[SlowTyper]

Found these two on local ads...



On top one says IRIS, no labels behind. Seems quite old and looks like some IBM Model F clone.

[TNT]

Looks very similar to Compaq's model F clones: wiki/Key_Tronic_Model_F_clone_series

[SlowTyper]

Looks very similar to Compaq's model F clones: wiki/Key_Tronic_Model_F_clone_series

So foam and foil

[XMIT]

Yes. The font and the lock LED location are giveaways.

[Keybug]

Strange Cherry fish, should be a pretty great little workhorse! Likely MX blacks under thin PBT keycaps. Does anyone know the model number?

[kbdfr]

Strange Cherry fish, should be a pretty great little workhorse! Likely MX blacks under thin PBT keycaps. Does anyone know the model number?

It’s a G81-8308, it has awful MY switches.
And yes, it is a pretty great little workhorse with 24 programmable keys, like its predecessor the G80-2100..

[Keybug]

Damn! And to think I just missed this beautiful NIB mother of a Siemens terminal keyboard...

[Keybug]

But then again, maybe it isn't G81! Thanks for pointing me in the right direction, though.

[dr-lipschitz]

Probably had nixie switches

[photekq]

Damn! And to think I just missed this beautiful NIB mother of a Siemens terminal keyboard...

So unlucky. That's such a beauty. I don't suppose there were any pictures of the label? I hope it turns up somewhere so we can at least identify it

Probably had nixie switches

Please stop commenting this on every Siemens/Nixdorf branded Cherry board The only boards with "Nixdorf blacks"/"Nixies" are the Nixdorf Softkeys boards [1] [2], which are easily differentiated from the Siemens/Nixdorf boards that were OEM'd by Cherry themselves.

[DJSwayde]

Probably had nixie switches

No, it probably did not.

[austinmc32]

Found this at work. wanted to know if its worth anything.

[Palatino]

The keyboard for the Siemens Dimension RXL chemical analyser, made by TG3 Electronics.

[Palatino]

viewtopic.php?f=2&t=3779

[Palatino]

They keycaps look nice - they would definitely get some interest on their own. As to the keyboard itself, it depends a bit on the connector and how usable it is. I for one like it: many strange buttons is a plus!

[austinmc32]

i like it too! honestly wouldn't mind selling it. But it is a ps2 connection on it. It was covered in plastic its whole life. sop the condition of it is very good.

[kbdfr]

But then again, maybe it isn't G81! Thanks for pointing me in the right direction, though.

The G80 version of the 8038 is not a Cherry model, but a modification made by a third party (don't remember the name at the moment), according to which they make them only with MX browns.

[apb]

gateway2kcl.png (203.61 KiB) Viewed 5975 times

any ideas? Looks like a Gateway anykey or some other rubberdome

edit: looks like it's this.
Gateway PS/2 2000 Keyboard (2196001-00-102)

[Lekrafter]

Def dome

[Keybug]

The G80 version of the 8038 is not a Cherry model, but a modification made by a third party (don't remember the name at the moment), according to which they make them only with MX browns.

Bugger, you were right, of course. G81 it is! Still, a great little tank of a board. Not sure I will be able to find a use for it, though. Typing on it is horrible, of course.

[kbdfr]

The G80 version of the 8038 is not a Cherry model, but a modification made by a third party (don't remember the name at the moment), according to which they make them only with MX browns.

Bugger, you were right, of course. G81 it is! Still, a great little tank of a board. Not sure I will be able to find a use for it, though. Typing on it is horrible, of course.

The innards of a G80-8000 would fit, but while the G80 has a flat cable as a connector, the G81 has a plastic sheet with printed tracks. Apparently no way to make the contacts fit, I fear, even if the connections have the same measurements and probably the same configuration.

But well, I'm not a keyboard tinkerer, of course.
Would be grateful for how-tos - preferably excluding soldering

[hellothere]

i like it too! honestly wouldn't mind selling it. But it is a ps2 connection on it. It was covered in plastic its whole life. sop the condition of it is very good.

PS/2 isn't a problem. PS/2 to USB adapters cost around $6 US. It would be nice if you remove a cap to show us the switches. I'm thinking Cherry, but I could be wrong.

Gotta love a keyboard that has both a "Meth" key and a "THC" key.

I'd probably put a bid on it, too. I also like lots of additional keys.

[Go-Kart]

gateway2kcl.png

any ideas? Looks like a Gateway anykey or some other rubberdome

edit: looks like it's this.
Gateway PS/2 2000 Keyboard (2196001-00-102)

Some regular Gateway 2000 boards feature Maxi Switch conductive dome with sliders.

[Palatino]

I've draw a blank on this switch - and the keyboard too. The switch is clicky, perhaps an Alps clone of some sort, but with a simple rectangular slider like an SMK 2nd Gen switch. Doesn't feel too bad at all. Does anyone recognize it?

Spoiler:

IMG_20210328_112747.jpg (2.45 MiB) Viewed 5791 times

IMG_20210328_112551.jpg (2.64 MiB) Viewed 5791 times

IMG_20210328_112906.jpg (4.27 MiB) Viewed 5791 times

IMG_20210328_112841.jpg (2.1 MiB) Viewed 5791 times

[Go-Kart]

I've draw a blank on this switch - and the keyboard too. The switch is clicky, perhaps an Alps clone of some sort, but with a simple rectangular slider like an SMK 2nd Gen switch. Doesn't feel too bad at all. Does anyone recognize it?

Spoiler:

IMG_20210328_112747.jpg

IMG_20210328_112551.jpg

IMG_20210328_112906.jpg

IMG_20210328_112841.jpg

I saw/bid on that Fullmark! I had the guy shoot me a pic of the switches and it just looked like an Alps clone but I couldn't discern anything further due to bad picture quality. Now I can see them better, it still doesn't help all that much

[Go-Kart]

Who made it/what does the PCB say?

[EricDauphinais]

Anyone has experience with this one?



The seller says it's Harris C1100 but I can't figure out what switches are in it. Thanks!

This looks a bit like NMB (space invader), but I could be wrong

Ordered one simply because I was too curious, now will need to figure out how to convert it...

[zrrion]

I've draw a blank on this switch - and the keyboard too. The switch is clicky, perhaps an Alps clone of some sort, but with a simple rectangular slider like an SMK 2nd Gen switch. Doesn't feel too bad at all. Does anyone recognize it?

It looks a lot like a KPT switch, but the top housing isn't quite right for that

[4_404]

I've draw a blank on this switch - and the keyboard too. The switch is clicky, perhaps an Alps clone of some sort, but with a simple rectangular slider like an SMK 2nd Gen switch. Doesn't feel too bad at all. Does anyone recognize it?

Spoiler:

IMG_20210328_112747.jpg
IMG_20210328_112551.jpg
IMG_20210328_112906.jpgIMG_20210328_112841.jpg

I have a Fullmark board with what looks like a white version of the same switch. I thought I identified the switch, but have subsequently forgotten what it was. My Fullmark board is identical to two other boards I have with ISNJK-168/268 FCC ID (Limtech) (one with SKCM white, one with AO2 clones), apart from the label and PCB - the same as wiki/Brain_KB-9001S, but without the RB88. Note the 368 number on the plate. Sorry for the garbage photos.

Spoiler:

IMG_20200805_170109~2.jpg (1.4 MiB) Viewed 5705 times

IMG_20200805_170050~2.jpg (1.69 MiB) Viewed 5705 times

IMG_20200803_100907~2.jpg (1.85 MiB) Viewed 5705 times

IMG_20200802_140302~2.jpg (2.53 MiB) Viewed 5705 times

IMG_20200802_100233~2.jpg (1.44 MiB) Viewed 5705 times